กลับไปที่บล็อก
คู่มือวิธีใช้ 2026-11-21 Dogtra 0 การดู

Charging Rubber Cap #T11 for 1900S Transmitter: Replacement Guide

Charging Rubber Cap #T11 for 1900S Transmitter: Replacement Guide

Learn how to identify, replace, and care for the Dogtra Charging Rubber Cap #T11 on your 1900S transmitter and other compatible models.

Why the Charging Rubber Cap Matters

The small rubber cap that covers the charging port on your Dogtra transmitter does a big job: it keeps dust, moisture, and debris out of the charging contacts. Over time, the cap can wear out, tear, or get lost. A missing or damaged cap leaves the charging port exposed, which can lead to poor charging contact or corrosion.

The Charging Rubber Cap #T11 is the correct replacement part for a wide range of Dogtra transmitters, including the 1900S, 1900NCP, 1902NCP, 200NCP Gold, 280NCP, 282NCP, 1400NCP, 1500NCP, 1600NCP, 1700NCP, 7000 series, 7100 series, M Plus, and H Plus models. It also fits many receivers, such as the 1900S, 1902S, 1800NC, ARC, and Edge RT. Check your device's serial number against the compatibility list to be sure.

Charging Rubber Cap #T11 Compatibility

  • CHARGING RUBBER CAP #T11 _1900S TRANSMITTER SERIES TRANSMITTER: Charging rubber cap #T11, for Dogtra transmitters: 200NCP Gold (S/N greater than 111361), 202NCP (S/N greater than 101961), 280NCP, 282NCP, 1400NCP, 1500NCP, 1600NCP, 1700NCP, 1900NCP, 1902NCP, 7000 series, 7100 series, M Plus, and H Plus. Receivers: 175NCP (S/N greater than 103471), 200NCP Gold (S/N greater than 111361), 202NCP (S/N greater than 101961), 280NCP, 282NCP, 280C, 282C, ARC, 1400NCP, 1500NCP, 1600NCP, 1700NCP, 1800NC (S/N greater than 100121), 1802NC (S/N greater than 100101), 1803NC (S/N greater than 100101), 1804NC (S/N greater than 100126), 1900NCP, 1902NCP, 1900S, 1902S, 2200NCP, 2300NCP, 2302NCP, 2500T&B, 2502T&B, 3500NCP, 3502NCP, Edge RT, EF-3000 Gold, YS300, YS500 (S/N greater than 30320), 7000 series, 7100 series, M Plus, and H Plus. *Sold individually* Knowing which models the #T11 cap fits helps you confirm it's the right part before you buy, avoiding a mismatch.
    CHARGING RUBBER CAP #T11 _1900S TRANSMITTER SERIES TRANSMITTER
    CHARGING RUBBER CAP #T11 _1900S TRANSMITTER SERIES TRANSMITTER

How to Replace the Charging Rubber Cap #T11

The replacement process is straightforward and takes only a minute. You'll need the new #T11 cap and your transmitter or receiver.

  1. Remove the old cap: Gently pull the existing rubber cap away from the charging port. If it's already missing, skip this step.
  2. Align the new cap: Position the new #T11 cap over the charging port. The cap is small and flexible; line it up so it covers the metal contacts completely.
  3. Press into place: Push the cap firmly but gently onto the port until it seats evenly. You should feel it snap or fit snugly around the edges.
  4. Test the fit: Give the cap a light tug to make sure it stays put. It should not come off easily. If it feels loose, remove it and press again, checking that the cap is not twisted.

Caring for Your New Charging Cap

To extend the life of the replacement cap, keep it clean and free of grit. Wipe it with a dry cloth if you notice dirt. Avoid using sharp objects to pry it off. The cap is sold individually, so it's a good idea to keep a spare on hand if you use multiple devices or train in dusty or wet conditions.

The supplied information does not include a recommended replacement interval. Inspect the cap periodically for cracks, tears, or loss of elasticity, and replace it when it no longer seals the port snugly.

What the Supplied Information Does Not Cover

The product record confirms compatibility but does not provide instructions for cleaning the charging port itself, nor does it specify a lifespan for the cap. If you have trouble getting a secure fit after replacement, check that the charging port on your device is clean and free of debris. For any further guidance, refer to your device's manual or contact Dogtra support.

บทความที่เกี่ยวข้อง

Customer Service
หน้าแรก
สินค้า
ตะกร้า
โปรไฟล์